How to Pull Out Dishwasher for Repair?

Your dishwasher may need to be replaced occasionally if it stops functioning or requires repair work. It might be a major hassle for many homeowners when that time arrives. In addition to buying a new dishwasher, you frequently have to get rid of the old one to install the new one.

Items You Need to Pull Out Dishwasher to Repair It

1. Gloves
2. Screwdriver
3. Crescent Wrench
4. Cardboard
5. Towel
6. Voltage/current Detector Pen

Follow our instructions to remove the dishwasher on your own quickly.

Step 1: Disconnect The Power Supply

Understanding how to disconnect a dishwasher from its power supply is critical before removing the appliance from the cabinet is critical. Find the circuit breaker. Change the breaker’s setting to “off.” You could hook your dishwasher into the socket under the sink. Remove the dishwasher’s plug from the outlet if this is the situation. Your dishwasher will be directly wired if there isn’t a plug under the sink.

Step 2: Disconnect The Water Supply

After unplugging the appliance from the outlet, you must turn off the supply line that supplies water to the dishwasher. The water supply shutdown valve is once again under the kitchen sink. To reach the supply connection on the wall, find the metal water supply line from your dishwasher and follow it there. Until it is tight, turn the supplied knob counterclockwise. Your dishwasher is no longer receiving any water now.

Step 3: Disconnect the Drain Line

Disconnecting the drain line for the dishwasher is necessary after you have completely disconnected the water supply line and the power supply. Unplug the drain hose from the garbage disposal by using a screwdriver to progressively remove the hose clamp’s screw until the hose is unplugged.

Step 4: Unfasten the Mounting Brackets

A dishwasher is typically secured by two metal mounting brackets screwed into the countertop’s base above the dishwasher. To find these brackets, open the dishwasher door and peek under the kitchen counter’s lip. The screws holding the dishwasher in place should be removed.

Step 5: Disconnect the Panel

The dishwasher has a panel covering the bottom that you can see. This panel, which is screwed onto the dishwasher, conceals the water supply, drain, and electricity supply. Use a screwdriver to find the screws and remove them from the frame. Remove the panel and discard the screws.

Step 6: Loosen the Dishwasher’s Front Legs

Four leveling legs—one at each corner—hold your dishwasher against the underside of the counter. Turn the leveling leg screw counterclockwise using a crescent wrench. You should be able to turn the leg with your fingers once the screw has been loosened. Adjust the two front legs so that there is about an inch between the foot of each leg and the ground. Your dishwasher will be able to be tipped and moved out from beneath the kitchen counter with a little more room, thanks to this.

Step 7: Loosen the Dishwasher’s Back Legs

Put a sizable piece of cardboard in front of the leveling legs of your dishwasher. Take hold of the base of your dishwasher and raise it onto the cardboard. Push the supply line from the sink area to behind the dishwasher to make it simpler. Reach under the dishwasher and unfasten the two back leveling legs after it has been moved a few feet from the counter. Use your fingers and crescent wrench to loosen the legs by about an inch.

Step 8: Pull out the Dishwasher

Undo all connections and attachments, and move your dishwasher from below the counter. Don’t damage your floor by scratching it. Lift just a little as you take the dishwasher out of the cabinet to prevent scratching the floor. You might want to cover the floors with a canvas drop cloth as you remove the appliance.

Now you can install the new dishwasher, or if you want to repair it, you can.

How to Install the Dishwasher?

You can easily install the dishwasher in a few easy steps.

Let’s look at these steps given below.

Step 1: Locate and remove the drain line connector cap.

Step 2: To run the drain line from the dishwasher area to under the sink, attach the drain line that came with the dishwasher, crimp the clamp around the hose with pliers, and thread the other end through the hole in the cabinet. Connect the water valve to the 90-degree fitting.

Step 3: Slide the dishwasher under the countertop using floor protection.

Step 4: Reattach the identical-colored wires, then secure them using wire nuts and electrical tape. The copper ground wire should be inserted underneath the green circular screw and tightened.

Step 5: Connect the water supply line to the 90-degree fitting and tighten it with a wrench. Before connecting the drain line to your garbage disposal or sink drain and tightening a clamp around the hose, run and fasten the drain line up to the countertop.

Step 6: Check for leaks after turning on the power and water again. Level the dishwasher under the counter using your level and a wrench to adjust the legs. Install screws to hold the dishwasher to the counter after it is level.

Conclusion

Now that you know how to remove and install a dishwasher, you can save money by doing it yourself or save time by hiring a skilled technician to complete the dishwasher installation. Call us for expert assistance.